Primary brake shoe

Rear Brake Shoe

The rear brake shoe refers to the part pushed outward by the action of the brake cam or push rod to suppress the brake drum for braking. It is installed on the brake drum and is one of the key safety parts in the automobile braking system. The rear brake shoes shall be replaced after 50000-80000km. The brake pad is a vulnerable part, and the replacement cycle of the brake pad is determined according to the driving habits of the owner; If the thickness of the brake pad of the vehicle is worn to 1/3 of the original thickness, it needs to be replaced. If the brake pad is not smoothed in time, the vehicle will lose control of braking and affect driving safety.

Precautions for primary brake shoes

Precautions for primary brake shoes are important when it comes to maintaining your vehicle’s safety. Primary brake shoes are a critical component of the braking system, and as such need to be properly maintained and inspected regularly. Here are some tips for keeping your primary brake shoes in top condition:

1. Inspect primary brake shoes regularly – Inspecting your primary brake shoes should be done every 10,000 miles or so. You will want to ensure that they are not worn down or cracked, as this can lead to less effective braking performance.

2. Replace worn out brake pads – If you notice that the material on the shoe is becoming thin, it’s time to replace them. Worn-out pads can cause the brakes to take longer time to stop your vehicle and can even lead to dangerous situations on the road due to decreased stopping power.

3. Clean brakes regularly – Dirt and debris can build up on the shoe which could lead to poor braking performance if left unchecked for too long. Make sure that you clean off all of the dirt with a damp cloth or compressed air before each use of your brakes in order to ensure optimal performance every time you hit the brakes!

Features and advantages of primary brake shoe

Primary brake shoes are an important part of any vehicle's braking system. They provide the friction necessary to slow down and stop a car, truck, or SUV. Primary brake shoes are made of strong, durable materials that can stand up to wear and tear. Here are some of their features and advantages:

1. Durability: Primary brake shoes are designed to withstand the high temperatures and pressures associated with braking, meaning they will last longer than other types of brakes.

2. Cost-effectiveness: Primary brake shoes are very cost-effective compared to other types of brakes, making them an attractive choice for budget-conscious drivers.

3. Easy installation: Primary brake shoes can be easily installed by experienced mechanics or DIYers with just a few basic tools.

4. Better performance: Primary brake shoes provide superior performance in terms of stopping power and control when compared to other types of brakes, making them ideal for those who need reliable performance from their vehicles on a daily basis.

5. Reduced noise levels: The friction generated by primary brake shoes is much quieter than other types of brakes, allowing you to enjoy quieter rides while still enjoying superior stopping power from your vehicle's braking system.

2005 2006 toyota tacoma rear brake shoe replacement

In general, the 2006 toyota tacoma rear brake shoe replacement wear much more slowly than the front - after all, they are only providing a small fraction of overall braking, and as drum brakes wear more slowly anyway. However, eventually they need to be changed - whether due to wearing out or - perhaps more commonly - due to a rear axle seal leak.

A rear axle seal leak was what caused me to do the job on both my 3rd gen 4Runner as well as 1st gen Tacoma , which you can read about if you're interested.

Whatever the reason for replacement, it's not a hard job, requires no special tools, and is one you can save a lot of money by doing yourself. So let's get started.

Replacement method of 2005 2006 toyota tacoma rear brake shoe:

1. Before replacing the 2005 2006 toyota tacoma rear brake shoe replacement, open the cover of the brake fluid reservoir in the engine compartment to see the height of the brake fluid page. If the brake fluid page is above the maximum limit, the brake fluid should be sucked out to prevent the brake fluid from overflowing during the replacement process;

2. Prepare the 2005 2006 toyota tacoma rear brake shoe replacement to be replaced and remove the wheel on which the brake is located. Avoid rim scratching during disassembly;

3. Remove the bolts of the brake caliper with a wrench and a socket, and then remove the brake skin (if there is a brake sensing line, remove the brake sensing line first). Observe whether the brake pad is excessively worn or cracked. If yes, replace it in the next step;

4. Since there will be a lot of sand or soil in the brake caliper, it is necessary to clean it with a rag, and then apply silencing paste to prevent abnormal noise during braking;

5. Use the piston pressure pump to press the piston to the position where it cannot be pressed, and then install the 2005 2006 toyota tacoma rear brake shoe replacement on the brake caliper. After the new brake pad is installed in place (it should also be installed if there is a brake induction line), tighten the guide bolt and complete the installation;

6. After installation, cover the reservoir, step on the brake pedal and reset the brake. Then observe the brake fluid height within the appropriate height range;

7. Test run after replacement to check whether the braking effect is reflected.

       Main Products from LONGWAY:

       1.Manual and automatic slack adjusters, all types

       2.Air brake chambers, all types

       3.Brake shoes, brake linings and brake shoe hardware kits

       4.S-camshaft and s-camshaft hardware kits

       5.Air brake line and air brake hoses

       6.Air brake valves

       7.Hub caps

       8.Glad hand / Palm coupling

Air brake shoes

The high-quality products of Hangzhou Longway Machinery mainly include Manual & automatic slack adjusters for European, American, Japanese, and South Korean market; Brake s-camshafts and repair kits; Spring brake chambers; Air Brake shoe assemblies and repair kits; Air brake valves; Quick release valve assemblies; Quick couplings assemblies; High-strength bolts and nuts, holders nylon washer chains, etc, nearly one thousand sorts and more than a dozen of series.

Air brake shoes in China

Mainly apply for: BPW, Volvo, YORK, SCANIA, TRAILER, ROR SAF, FREHAUF, MERCEDES, MAN, ZF, DAF, RENAUT, RABA, NEOPLAN, TEC, SMB, RVI, BENDIX, MERITOR, SPICER, EATON, UNIVERSAL, WAGNER, HENDRICKSON, DEXTER, MACK, HINO, Nissan, MITSUBISHI, ISUZU and so on. To buy Air brake shoes, look for Longway Machinery, a professional Air brake shoes manufacturer.

Longway Machinery is one of the leading Brake chamber, Automatic slack adjuster OEM, Suppliers. The price is low, and the quality is good. Have a lot of foreign long-term customers. Our product quality has passed international certification, and the price is affordable. To order Air brake shoes, choose Longway Machinery, a professional Air brake shoes manufacturer.

Find Air brake shoes for your production line Get more details of Air brake shoes from Longway Machinery and contact us to get price quotation. Welcome to call and order our products.

　　Q: Are you a trading company or factory?

　　A: We are the manufacturer with trading company independent.

 　  Q: What's the MOQ for each item?

　　A: Usually the MOQ is 50pcs for each type. If a color box is requested, the MOQ is 200pcs.

　　Q: What about the delivery time?

　　A: It's about 30 to 45 days for the goods to need to be manufactured, based on your order.

　　Q: Do you give any guarantee to your products?

　　A: Basically, the lifetime of the automatic slack can reach 2 years or 200 thousand kilometers under normal use, no over loading and the road condition is good.