Air brake shoes SAF180

Rear Brake Shoe

The rear brake shoe refers to the part pushed outward by the action of the brake cam or push rod to suppress the brake drum for braking. It is installed on the brake drum and is one of the key safety parts in the automobile braking system. The rear brake shoes shall be replaced after 50000-80000km. The brake pad is a vulnerable part, and the replacement cycle of the brake pad is determined according to the driving habits of the owner; If the thickness of the brake pad of the vehicle is worn to 1/3 of the original thickness, it needs to be replaced. If the brake pad is not smoothed in time, the vehicle will lose control of braking and affect driving safety.

2005 2006 toyota tacoma rear brake shoe replacement

In general, the 2006 toyota tacoma rear brake shoe replacement wear much more slowly than the front - after all, they are only providing a small fraction of overall braking, and as drum brakes wear more slowly anyway. However, eventually they need to be changed - whether due to wearing out or - perhaps more commonly - due to a rear axle seal leak.

A rear axle seal leak was what caused me to do the job on both my 3rd gen 4Runner as well as 1st gen Tacoma , which you can read about if you're interested.

Whatever the reason for replacement, it's not a hard job, requires no special tools, and is one you can save a lot of money by doing yourself. So let's get started.

Replacement method of 2005 2006 toyota tacoma rear brake shoe:

1. Before replacing the 2005 2006 toyota tacoma rear brake shoe replacement, open the cover of the brake fluid reservoir in the engine compartment to see the height of the brake fluid page. If the brake fluid page is above the maximum limit, the brake fluid should be sucked out to prevent the brake fluid from overflowing during the replacement process;

2. Prepare the 2005 2006 toyota tacoma rear brake shoe replacement to be replaced and remove the wheel on which the brake is located. Avoid rim scratching during disassembly;

3. Remove the bolts of the brake caliper with a wrench and a socket, and then remove the brake skin (if there is a brake sensing line, remove the brake sensing line first). Observe whether the brake pad is excessively worn or cracked. If yes, replace it in the next step;

4. Since there will be a lot of sand or soil in the brake caliper, it is necessary to clean it with a rag, and then apply silencing paste to prevent abnormal noise during braking;

5. Use the piston pressure pump to press the piston to the position where it cannot be pressed, and then install the 2005 2006 toyota tacoma rear brake shoe replacement on the brake caliper. After the new brake pad is installed in place (it should also be installed if there is a brake induction line), tighten the guide bolt and complete the installation;

6. After installation, cover the reservoir, step on the brake pedal and reset the brake. Then observe the brake fluid height within the appropriate height range;

7. Test run after replacement to check whether the braking effect is reflected.

       Main Products from LONGWAY:

       1.Manual and automatic slack adjusters, all types

       2.Air brake chambers, all types

       3.Brake shoes, brake linings and brake shoe hardware kits

       4.S-camshaft and s-camshaft hardware kits

       5.Air brake line and air brake hoses

       6.Air brake valves

       7.Hub caps

       8.Glad hand / Palm coupling

Air brake shoes

The high-quality products of Hangzhou Longway Machinery mainly include Manual & automatic slack adjusters for European, American, Japanese, and South Korean market; Brake s-camshafts and repair kits; Spring brake chambers; Air Brake shoe assemblies and repair kits; Air brake valves; Quick release valve assemblies; Quick couplings assemblies; High-strength bolts and nuts, holders nylon washer chains, etc, nearly one thousand sorts and more than a dozen of series.

Air brake shoes in China

Mainly apply for: BPW, Volvo, YORK, SCANIA, TRAILER, ROR SAF, FREHAUF, MERCEDES, MAN, ZF, DAF, RENAUT, RABA, NEOPLAN, TEC, SMB, RVI, BENDIX, MERITOR, SPICER, EATON, UNIVERSAL, WAGNER, HENDRICKSON, DEXTER, MACK, HINO, Nissan, MITSUBISHI, ISUZU and so on. To buy Air brake shoes, look for Longway Machinery, a professional Air brake shoes manufacturer.

Longway Machinery is one of the leading Brake chamber, Automatic slack adjuster OEM, Suppliers. The price is low, and the quality is good. Have a lot of foreign long-term customers. Our product quality has passed international certification, and the price is affordable. To order Air brake shoes, choose Longway Machinery, a professional Air brake shoes manufacturer.

Find Air brake shoes for your production line Get more details of Air brake shoes from Longway Machinery and contact us to get price quotation. Welcome to call and order our products.

　　Q: Are you a trading company or factory?

　　A: We are the manufacturer with trading company independent.

 　  Q: What's the MOQ for each item?

　　A: Usually the MOQ is 50pcs for each type. If a color box is requested, the MOQ is 200pcs.

　　Q: What about the delivery time?

　　A: It's about 30 to 45 days for the goods to need to be manufactured, based on your order.

　　Q: Do you give any guarantee to your products?

　　A: Basically, the lifetime of the automatic slack can reach 2 years or 200 thousand kilometers under normal use, no over loading and the road condition is good.